Yaskawa Absolute Encoder Plug-in UTSAH-B17BBF For SGMDH-45A2AB ready to be installed

UTMAH-B12BD8V - Yaskawa - Internal encoders
UTMAHB12BD8V - Yaskawa - Internal encoders
UTMAH-B12BDYR7 - Yaskawa - Internal encoders
UTMAHB12BDYR7 - Yaskawa - Internal encoders
UTMAH-B12BDYR6 - Yaskawa - Internal encoders
UTMAHB12BDYR6 - Yaskawa - Internal encoders
UTMAH-B15AS8F - Yaskawa - Internal encoders
UTMAHB15AS8F - Yaskawa - Internal encoders
UTMAH-B15AS19B - Yaskawa - Internal encoders
UTMAHB15AS19B - Yaskawa - Internal encoders
UTMAH-B15AS4OB - Yaskawa - Internal encoders
UTMAHB15AS4OB - Yaskawa - Internal encoders
UTMAH-B15BS13 - Yaskawa - Internal encoders
UTMAHB15BS13 - Yaskawa - Internal encoders
UTMAH-B15AR - Yaskawa - Internal encoders
UTMAHB15AR - Yaskawa - Internal encoders
UTMAH-B15DSB - Yaskawa - Internal encoders
UTMAHB15DSB - Yaskawa - Internal encoders
UTMAH-B15AS3DB - Yaskawa - Internal encoders
UTMAHB15AS3DB - Yaskawa - Internal encoders
UTMAH-B15AS158 - Yaskawa - Internal encoders
UTMAHB15AS158 - Yaskawa - Internal encoders
UTMAH-B15AS4NB - Yaskawa - Internal encoders
UTMAHB15AS4NB - Yaskawa - Internal encoders
UTMAH-B15AS15B - Yaskawa - Internal encoders
UTMAHB15AS15B - Yaskawa - Internal encoders
UTMAH-B15AS4MB - Yaskawa - Internal encoders
UTMAHB15AS4MB - Yaskawa - Internal encoders
UTOPE-40AWT - Yaskawa - Internal encoders
UTOPE40AWT - Yaskawa - Internal encoders
UTOPE-25ZDL - Yaskawa - Internal encoders
UTOPE25ZDL - Yaskawa - Internal encoders
UTOPE-300WB80 - Yaskawa - Internal encoders
UTOPE300WB80 - Yaskawa - Internal encoder

Installing the Option
Refer to the instructions below to install the option.
1. Shut off power to the drive, wait the appropriate amount of time for voltage to
dissipate, then remove the digital operator (E), front cover (D), and terminal cover
(F). Refer to the Quick Start Guide packaged with the drive.
DANGER! Electrical Shock Hazard. Disconnect all power to the drive and wait at least the amount of time
specified on the drive front cover safety label. After all indicators are off, measure the DC bus voltage to
confirm safe level, and check for unsafe voltages before servicing to prevent electric shock. The internal
capacitor remains charged even after the power supply is turned off.
NOTICE: Damage to Equipment. Observe proper electrostatic discharge procedures (ESD) when handling
the option, drive, and circuit boards. Failure to comply may result in ESD damage to circuitry.

Prepare and connect the wire ends as shown in Figure 6 and Figure 7. Refer to
Wire Gauges and Tightening Torques on page 28 to confirm that the proper tightening torque is applied to each terminal. Take particular precaution to ensure
that each wire is properly connected and wire insulation is not accidentally pinched
into electrical terminals.
WARNING! Fire Hazard. Tighten all terminal screws according to the specified tightening torque. Loose
electrical connections could result in death or serious injury by fire due to overheating electrical connections.
Tightening screws beyond the specified tightening torque may result in erroneous operation, damage the
terminal block, or cause a fire.
NOTICE: Heat shrink tubing or electrical tape may be required to ensure that cable shielding does not
contact other wiring. Insufficient insulation may cause a short circuit and damage the option or drive.